Chinese

cart

(0)

▽

Air Mould Installation Treasure Book! With it, the bosses and their relatives are great!

Categories:test
Author:
Origin:
Time of issue:2019-07-10 13:43
Views:43

(Summary description) Keep away from sharp objects when using pneumatic products.

Air Mould Installation Treasure Book! With it, the bosses and their relatives are great!





Air Mould Installation Treasure Book! With it, the bosses and their relatives are great!

(Summary description) Keep away from sharp objects when using pneumatic products.

Categories:test
Author:
Origin:
Time of issue:2019-07-10 13:43
Views:43

Information

1. Open the air mold product from the packaging bag and lay it flat on the floor to be placed. First check whether the gas mould product is damaged and tighten the zipper cover. (Generally, the position of the zipper cover is at the bottom of the gas mold

product, and there are some special shapes, as well as the zipper cover at the top)

2. Connect the wires, according to the appropriate position to connect the wires, the fan of the general gas model product is 220V (our is no exception Ha), the normal electric voltage is appropriate.

3. Connect the fan tube of the air mould with the fan and connect the power supply. On both sides of the air mold, pull the rope to prevent the air mold from being compressed by the wind or the air mold product itself, swaying left and right, to a certain extent, to ensure the orderly inflatable standing of the air mold.

4. After confirming the stability of the gas mould product, the pulling rope will be stabilized at the fixed point to ensure the more stable of the gas mould product. When necessary, nail the ground (fittings are available) and hang the pull ring (air mold edge near the ground position has a special design) .

Matters needing attention:

1. In order to protect the air mold products to a greater extent, please pre-lay some waste carpets on the ground to reduce wear and tear before installing the aeration.

2. Do not turn off the power when the gas mold product is inflated. No sundries are allowed in the air inlet of the fan, so as not to be involved and cause damage to the fan. Frequently check the use of the fan, abnormal noise should be immediately stopped to check the reasons, after troubleshooting can be used .

When moving the gas mold products, do not pull the bottom of the gas mold, when it is necessary to move the gas mold products, many people can lift and move together.

3. In the case of long-term outdoor placement of air mold products, do not inflate them day and night for a long time. When collecting the gas mould product, let the gas mould product deflate by itself. Do not force the pressure extrusion gas mould product to achieve the purpose of rapid deflation. After deflation, please cover the sand bags on the air mold products, and ensure that no scratches are scratched onto the road surface or other barriers.

4. The air mold is an inflatable model, easy to tear, relatively low stability. Therefore, in the case of strong wind and heavy rain, do not use inflatable. The larger the air mold shape, the greater the influence of wind and external. If the height is above 10 meters, do not use the air above 5 degrees .

5. Keep away from sharp objects when using pneumatic products. The stability of the air mould is basically based on sand bags and nail pulling rings. Do not use other sharp objects such as stones, iron frames, etc .

Previous: Bosses: How to use the air model for amusement? You must be a layman!

Next: Rainbow Gate--the indispensable redness of wedding celebrations

Previous: Bosses: How to use the air model for amusement? You must be a layman!

Next: Rainbow Gate--the indispensable redness of wedding celebrations

Enterprise core competence

R&D Capability

ODM Service: Yes

Number of R&D Staff: 5-10 People

Trade Capability

Export Experience: 9 years

Trade Staff: 11-20 People

Production Capability

Production Lines: Above 10
Output Value: USS5 Million-USS10

OEM Capability

ODM Service: Yes

OEM Experience: 10 years

Quality Contro

QC Staff: Less than 5 People

One-stop air model product customization service

搜索

Search





Contact Us
Tel : +86-20-31000084
Tel : +86-1866-5623-629
Email : merry@bingoinflatables.com
WeChat : 18665623629
Factory : 107,No.2 MafengGang,Zengbian Country,
Xinzao Town,Panyu District,
Guangzhou City,Guangdong Province,China.
Office : Room 410,Jianqi Building,No.5,
Wenming Road,Nancun Town,Panyu District,
Guangzhou,Guangdong,China.